FOR more than 50 years Ronacrete has been manufacturing specialist flooring solutions for the industrial flooring sector, says the company.

‘In that time, we’ve formulated and developed a wide range of high spec products and systems that are used daily including factory produced polymer screeds, polymer admixtures, fast-drying screed additives, rapid-setting cementitious floor repairs, epoxy screeds and epoxy floor-coatings. One of those products is RonaScreed FastDry Prompt.

‘RonaScreed FastDry Prompt is a fast-drying screed additive which enables a 50mm thick sand/ cement screed to be overlaid with moisture sensitive floorings such as resilient floorings, carpet, quarry tiles, ceramic tiles and stone tiles after only four days of air-curing in good drying conditions.’ The company continues: ‘Ronacrete Laboratory tests and independent tests by Vinci Technology confirm the predictability of results shown in the technical data. RonaScreed FastDry Prompt gains strength at a faster rate than a typical sand cement screed and strengths greater than 20N/sq mm are achievable after only 24 hours at 20deg C, allowing early access to following trades.

‘RonaScreed FastDry Prompt has been used for decades where construction programs are compressed, leaving little time for a sand/ cement screed to dry and where contractors wish to reduce the incidence of damage to screed by following trades, by having screeds applied later in the construction program than would otherwise be possible.

‘RonaScreed FastDry Prompt has been extensively used in the education sector, particularly where underfloor heating is specified, and the product was specified as standard for screeds in schools and colleges by several county architects’ departments.’

Drying of standard sand/cement screeds
BS 8204-1 ‘Concrete bases and cementitious levelling screeds to receive floorings — Code of practice’ section 6.11.1 suggests the following calculation for drying of screeds with no fast-drying additive: ‘With levelling screeds, one day should be allowed for each millimetre of thickness for the first 50mm, followed by an increasing time for each millimetre above this thickness. It’s therefore reasonable to expect a levelling screed 50mm thick, drying under good conditions, to be sufficiently dry in about two months.’

It’s generally accepted that for between 50-75mm thickness, two days should be allowed for drying of each millimetre of thickness and a 75mm thick screed with no additive might be expected to take 100 days to dry to 75% humidity in good drying conditions.

In poor drying conditions when humidity is high and/or temperature is low, drying may take considerably longer, especially if moisture evaporating from screed and plaster isn’t extracted by open windows and doors or other means.

Testing conditions
When comparing specific drying claims made by other producers, it’s advisable to look at the drying conditions under which samples were tested.

Says the company: ‘Ronacrete products are tested after drying at a room temperature of 200C temperature and 60-65% air humidity. Tests carried out on samples cured at higher temperature and lower air humidity will produce apparently better drying data, the specifier or contractor should consider how close the curing conditions are to the reality of site conditions.’

Limiting factors
There are several key factors involved in how quickly flooring may be applied to a screed:

Drying of RonaScreed FastDry Prompt Mix Design 1 (3:1 by weight) has been tested at 50mm, 75mm and 100mm thickness. At 50mm thickness, RonaScreed FastDry Prompt Mix Design 1 dries to 75% RH after eight days of air curing, nine days at 75mm thickness and 10 days at 100mm.

75% relative humidity at the surface indicates the screed is sufficiently dry for application of resilient floorings, carpet, quarry tiles, ceramic tiles, and stone tiles.

Ronacrete Laboratory tests and independent tests by Vinci Technology confirm the predictability of results shown in the technical data. Drying time onsite will vary according to site conditions. Increased screed thickness, lower temperature and higher humidity will lengthen the drying period; increasing the aggregate/ cement ratio will also increase drying time.

Screeds should be sufficiently dry and strong before forced drying or commissioning of underfloor heating (UFH) commences, RonaScreed FastDry Prompt Mix Design 3 dries to 80% RH after about two days of air-curing at a thickness of 75mm and will gain a high proportion of its ultimate strength after the same period of curing.

At this stage, forced drying or commissioning of UFH may commence, UFH may be turned on and the temperature may be gradually increased in accordance with the instructions of the heating manufacturer. Forced drying or commissioning of UFH should be delayed at lower temperature and when air humidity is high or when RonaScreed FastDry Prompt has been added to a weaker mix design.